Thomas Hoffman
Maybe I should get one for her bike! She might tell me where she hid mine.
LOL
Of course I will need to go get a case of sunny delight, a tube of Zip ties,
and some duct tape so I can make some more fenders. Has anybody had any luck
with wire hangers as fender stays?
;-)
Tom
-----Original Message-----
From: Dave German [mailto:dave_g-@hotmail.com]
Sent: Monday, January 23, 2006 2:18 PM
To: t.hoff-@verizon.net; twotireti-@yahoo.com;
eva-@ci.hillsboro.or.us; ob-@topica.com
Subject: RE: [OBRA Chat] Rain Flap Tip
Hey do they make that same model with the chrome naked trucker guy with the
billboard hat??
From: Thomas Hoffman <t.hoff-@verizon.net>
Reply-To: t.hoff-@verizon.net
To: twotireti-@yahoo.com, 'Evan MacKenzie'
<eva-@ci.hillsboro.or.us>, ob-@topica.com
Subject: RE: [OBRA Chat] Rain Flap Tip
Date: Mon, 23 Jan 2006 10:54:22 -0800
I picked up a cool trucker mud flap at Bike Gallery last year. I Love it!
Easy to install and does the job, did I mention it's a TRUCKER Mud Flap
with a Chrome Lady and everything? My daughter hid it from me so I
couldn't put it on my bike.
"Actually my ski rack is held on to the roof of my car right now with
plastic ties...'
Note to self...
DO NOT follow John when driving to the mountain.
Seriously, the damage to your toys should be the least of your worries, the
guy in the car behind you is worth more than the money you saved on your
ski
rack.
Tom
_____
From: john schmidt [mailto:twotireti-@yahoo.com]
Sent: Monday, January 23, 2006 10:44 AM
To: Evan MacKenzie; ob-@topica.com
Subject: RE: [OBRA Chat] Rain Flap Tip
Well my tip is for people who do not want to deal with the hassle of
bolting
since:
Now you're looking at 15 minutes to half hour to install using a bolt
versus
less than just a couple minutes.
Now you are looking at more weight equals higher chance of fender breaking
and vibrating.
Milk jug plastic is extremely flexible and tough and cheap and readily
available. There is no need to twist it up for placing on rack. It will
flex. You want the weak part to be the flap not your fender ! A plastic
tied flap is typically on much more securely then with a bolt, (the "joint"
is spread out versus concentrated forces..unless you use curved fender
washers with the bolt method or fabricated sheet metal "washer" which only
add more weight to vibrate and more fabrication time, yes I know by
experience... )
And if the flap really gets in the way, well snip the ties and take off the
flap, and reinstall later. plastic tie are cheap.
But I also ride my bike and rarely give my bicycle a ride. especially in
the
winter.
I've mounted a whole fender with plastic ties (well except for the steel
rods from the eyelets of course) by stratagically drilling holes and
combining the plastic ties..
And then if you get the real big plastic ties they make good handcuffs too.
Actually my ski rack rack is held on to the roof of my car right now with
plastic ties...
John
Evan MacKenzie <eva-@ci.hillsboro.or.us> wrote:
All sounds good except...
I prefer to actually bolt mine to the existing fender. This allows the
attached piece, be it half an old water bottle or whatever, to rotate.
That way you can twist it up. If your fender extension on the front
fender does not rotate, forget putting the bike on pretty much any fork
mount roof rack with a tray to the rear wheel.
Evan
------------- __o
---------- _ '\<,_
----------(_)/ (_)______Get on your bikes and ride!
-----Original Message-----
From: john schmidt [mailto:twotireti-@yahoo.com]
Sent: Monday, January 23, 2006 9:59 AM
To: ob-@topica.com
Subject: [OBRA Chat] Rain Flap Tip
I thought I would share
putting those rain flaps the bottom of back fender is is nice for group
riding and the flap in the front keeps feet dryer and your chain much
much cleaner.
I found the easiest way to mount flaps is to just drill a couple holes
and "stitch" on the flaps with plastic ties. (this shouldn't take you
more than 5 minutes)
1. Find an old milk jug or similar plastic (you want light weight).
2. Cut out a strip (you can always trim later..)
3. Tape to fender (to hold in place for drilling)
4. Drill two vertically aligned holes about 1/2" apart on each "side"
of the fenders. four holes total. ( 1/8" or larger drill?) Remove the
wheel so you don't accidently drill into your tire !!!
5. run Plastic ties through the holes... Wire could work too,
basically you are just stitching the flap to the fender.
The concavity of the fender will "stiffen" the flap. But I've found even
if it doesn't it still works just fine if long enough. you can also
drill holes down the length of the flap and run a wire through and down
or double up the plastic. You want these things almost all the way to
the ground.
I found in general, plastic ties
To respond to the whole group send to ob-@topica.com.
To respond to the list manager send to cmur-@obra.org
To unsubscribe send to obra-uns-@topica.com
To respond to the whole group send to ob-@topica.com.
To respond to the list manager send to cmur-@obra.org
To unsubscribe send to obra-uns-@topica.com